Woodpro

Woodpro Water-Based Sealer

PrintEmail

A penetrating wood sealer based on a water-based acrylic resin, which provides a natural matt finish that nourishes, seals and protects wood surfaces.

Products Applications:
Wood (Interior & Exterior), Wood (Interior), Wood (Exterior) and Sealer (Wood)

Purchase:
Prominent Woodpro Water-Based Sealer is available in the following sizes: 1lt and 5lt 


Description

Appearance: Matt finish
Colours: Clear 
Solids: 15% by mass; 14% by volume.
Density: 1,02 kg/litre.
Spreading Rate: 10m²/litre. The practical spreading rate will depending on the porosity and profile of the wood as well as the application technique and tools used.
Viscosity at 23°C: 10 seconds FC4
Flash Point: Non Flammable.

Respecting The Environment:

  • 100% Lead Free & Low VOC.
  • Dispose of excess product and containers in a responsible manner without harming the environment.
  • This product is manufactured under strict SABS ISO 9001 quality standards.

Storage:

  • Keep containers properly sealed.
  • Store away from direct heat, sun and severe cold in a place with adequate ventilation.

Available Sizes: 1Lt, 5Lt

Features

  • Matt finish.
  • Environmentally friendly with a low odour.
  • UV resistant, with good fungal protection.
  • Water resistant - prevents water penetration.
  • Non-Yellowing.
  • Excellent adhesion and abrasion resistance.
  • Water based – easy cleaning and quick drying.

Intended Usages

  • Doors and window frames.
  • Furniture, skirting boards and cupboards.

Application Details

  • Mixing: Stir well before use with a flat paddle to a homogenous consistency. Stir occasionally during use.
  • Method: Brush, sponge or airless spray gun.
  • Thinning: Not recommended.
  • Cleaning: Remove as much of the product as possible from the application equipment before cleaning with water.

Application Conditions:

  • Surface temperature - Min: 10°C or 2°C minimum above dew point, if possible away from direct sunlight.
  • Relative humidity of less than 10%.

Drying time: 
Touch dry 30min at 23°C/ Overcoating 4h at 23°C / Hard Dry 24h at 23°C. 
Note:
  Higher temperatures will accelerate the drying times (approximately halved for every 10°C increase), whilst lower temperatures will retard the drying time (approximately doubled for every 10°C decrease).

Requirements:
 2 - 4 coats

Surface Preparations

All surface to be clean dry and sound. Remove any oil, grease, plaster splatter, etc. 

New Wood: 

  • Sand the surface with 150-180 grit sandpaper (sand with the grain to eliminate damage to wood surface).
  • Remove sanding dust from surface with a clean damp cloth or paintbrush.

Previously varnish wood in all conditions: 

  • Strip completely by deep sanding or by using a paint stripper for wood.
  • Rinse thoroughly with clean water to neutralise and allow drying.
  • Sand to a smooth surface finish. Remove dust with a damp cloth.

Previously coated with a wax sealer/oil based wood preservative: 

  • Mechanically sand until raw wood is exposed with no product residue. Remove dust with a damp cloth. down and treat as new wood.

Weathered or Discoloured wood: 

  • Remove the weather or discoloured layers by sanding with a 100 grit sandpaper to an even smooth finish.
  • Remove dust with a damp cloth. Alternatively treat wood with a wood reviver to remove any weather damage and to neutralise the wood surface, allow drying. Sand to a smooth finish. Remove dust with a damp cloth.
    completely by deep sanding or by using a paint stripper for wood.
  • Rinse thoroughly with clean water to neutralise and allow drying.
  • Sand to a smooth surface finish. Remove dust with a damp cloth.

Previously painted wood:  

  • Strip completely by deep sanding or by using a paint stripper for wood.
  • Rinse thoroughly with clean water to neutralise and allow drying.
  • Sand bare wood to a smooth surface finish. Remove dust with a damp cloth.

Application:  

  • All surfaces to be coated should be sound, clean, dry and free from sawdust and loose, flaking material after using the correct preparation method and products.
  • Stir product regularly with a flat paddle to achieve an even consistency before and during application process.
  • Apply product using the application method icons guideline.
  • Apply at least 3 to 4 coats on new wood.
  • Lightly sand with fine sandpaper or steel wool between coats to ensure a smooth finish.

Limitations

  • As with all wood coating products routine inspections are needed every 3-6 months. It is recommended to apply a maintenance coat every 6 months or when the wood appears dry to prolong the life of the WOODPRO WATERBASED SEALER.
  • Can only be applied under specified conditions.
  • Cannot be applied directly over previous wood treatments without the correct preparation first.
  • When coating exterior wood special attention must be given to the adequate sealing and coating of the end grain.
  • Only apply product to dry wood in a dust free environment.
  • To ensure a consistent appearance ensure that the batch numbers on all containers are the same. Where batch numbers on containers differs intermix before use.
  • Not for use below ground level.
  • Not for use on exterior decking wood or interior floor.
  • Cannot be tinted with Universal Stainer.

Safety

  • Keep out of reach of children.
  • Ensure to maintain good ventilation during application and drying process.
  • Wear a suitable dust mask if sanding.
  • In case of accidental skin contact, wash with soap and water or a recognised skin cleaner. Avoid contact with eyes. In case of contact with eyes rinse immediately with running water and seek medical advice.
  • If product is ingested drink plenty of water. Do not induce vomiting at any time. Seek medical advice.
  • Do not smoke while painting.
  • To avoid any risk of spillage, always transport in a secure upright position.
  • Refer to the Material Safety Data Sheet (MSDS) for detailed information about the product and transportation and classification criteria. MSDS is available on www.prominentpaints.co.za or from Prominent Customer Service Department.
  • Keep out of reach of children.
  • Ensure to maintain good ventilation during application and drying process.
  • Wear a suitable dust mask if sanding.
  • In case of accidental skin contact, wash with soap and water or a recognised skin cleaner. Avoid contact with eyes. In case of contact with eyes rinse immediately with running water and seek medical advice.
  • If product is ingested drink plenty of water. Do not induce vomiting at any time. Seek medical advice.
  • Do not smoke while painting.
  • To avoid any risk of spillage, always transport in a secure upright position.
  • Refer to the Material Safety Data Sheet (MSDS) for detailed information about the product and transportation and classification criteria. MSDS is available on www.prominentpaints.co.za or from Prominent Customer Service Department.

Copyright © 2017 Prominent Paints