Trade

Promodek

PrintEmail

Low VOC interior/exterior emulsion based paint with excellent hiding power.

Products Applications:
Primers and Ceilings (Interior)

Purchase:
Prominent Promodek is available in the following sizes: 1Lt, 5Lt, 20Lt


Description

Appearance: Matt.
Spreading Rate: 4 - 8 m²/l dependent on surface texture and porosity.
Solids: ± 50% by mass.
Density: ± 1,35 kg/litre.
Recommended Dry Film Thickness: 2 coats at 40 µm per coat minimum.
Viscosity: ± 115 Kµ.
Flash Point: Non-flammable.

Storage:

  • Keep containers properly sealed.
  • Store away from direct heat, sun and severe cold in a place with adequate ventilation.

Available Sizes: 1Lt, 5Lt, 20Lt
Colours: White.
Calculated Maximum VOC: 16g/L maximum for white.

Respecting The Environment:

  • 100% Lead Free & Low VOC.
  • Dispose of excess product and containers in a responsible manner without harming the environment.
  • This product is manufactured under strict SABS ISO 9001 quality standards.

Features

  • Waterbased: Low odour, easy cleaning.
  • Excellent hiding power.
  • Wipeable.
  • Matt finish: Does not highlight imperfections like a sheen or high gloss paint.
  • Alkali resistant: Can be applied directly to cement plaster.
  • 100% lead free and low VOC: Reduces the odour associated with painting indoors.

Intended Usages

  • Direct application to interior cement plaster and unglazed bricks.
  • Suitable for gypsum board ceilings.

Application Details

  • Mixing: Stir before use with a flat paddle to an even consistency. Stir occasionally during use.
  • Method: Roller, brush or airless spray.
  • Thinning: Not recommended.
  • Cleaning: Remove as much of the product as possible from the application equipment before cleaning with tap water.

Conditions:

  • Temperature between 5°C and 40°C.
  • Relative humidity of less than 85%, preferably between 10:00 and 16:00.
  • Ideally apply when the temperature of the substrate is at least 2°C above dew point.
  • If possible away from direct sunlight.

Drying time:
Touch dry - 30 minutes. 
Note: Higher temperatures will accelerate the drying times (approximately halved for every 10°C increase), whilst lower temperatures will retard the drying time (approximately doubled for every 10°C decrease).

Recoating time:

4 hours at 23°C.

Requirements:
Two coats.

Surface Preparations
Sound cement plaster:

  • Direct - no primer required.

Gypsum ceiling boards:

  • Direct - no primer required.

Gloss enamel:

  • Sand well, clean and apply Prominent Premium Universal Undercoat.

Emulsion paint:

  • Clean well and apply directly.

Chalky surfaces:

  • Wire brush/high-pressure water jet, allow drying and then apply one coat Prominent Dampcure or Prominent Surface Restorer.

Poor condition surfaces, i.e. excessive peeling:

  • Strip down and treat as new work.

Limitations

  • Cannot be applied in cold and moist conditions.
  • Product can not accommodate excessive movement i.e. hairline cracking or application onto flexible coatings like texture coats and waterproofing systems.
  • Cannot be used on excessively rough plasters as varying thickness in the coating can lead to mud cracking.
  • Chalking takes place due to UV exposure.
  • Tinting not recommended.
  • Not for use as finishing coat in bathrooms and kitchens.
  • The low VOC compliance is applicable for batches manufactured from 1 September 2010 onwards.

Safety

  • Keep out of reach of children.
  • Ensure to maintain good ventilation during application and drying process.
  • In case of skin contact, wash with soap and water or a recognised skin cleaner. Avoid contact with eyes. In case of contact with eyes rinse immediately with running water and seek medical advice.
  • If product is ingested drink plenty of water or milk. Do not induce vomiting at any time. Seek medical advice.
  • Refer to the Material Safety Data Sheet (MSDS) for detailed information about the product and transportation and classification criteria. MSDS is available on www.prominentpaints.co.za or from Prominent Customer Service Department.
  • To avoid any risk of spillage, always transport in a secure upright position.

 

  • Keep out of reach of children.
  • Ensure to maintain good ventilation during application and drying process.
  • In case of skin contact, wash with soap and water or a recognised skin cleaner. Avoid contact with eyes. In case of contact with eyes rinse immediately with running water and seek medical advice.
  • If product is ingested drink plenty of water or milk. Do not induce vomiting at any time. Seek medical advice.
  • Refer to the Material Safety Data Sheet (MSDS) for detailed information about the product and transportation and classification criteria. MSDS is available on www.prominentpaints.co.za or from Prominent Customer Service Department.
  • To avoid any risk of spillage, always transport in a secure upright position.

Copyright © 2017 Prominent Paints