Speciality

Speciality Surface Sealer

PrintEmail

A clear silicone based water repellent sealer.

Products Applications:
Waterproofing

Purchase:
Prominent Surface Sealer is available in the following sizes: 1lt , 5lt and 20lt 


Description

Appearance: Clear/Matt.
Spreading Rate: 3 - 6 m²/litre dependent on surface texture and porosity.
Solids: ± 6%
Density: ± 0,80 kg/litre.
Recommended Dry Film Thickness: Not applicable.
Viscosity: Thin liquid.
Flash Point: 43°C.

Storage:

  • Keep containers properly sealed.
  • Store away from direct heat, sun and severe cold in a place with adequate ventilation.

Available Sizes: 1Lt, 5Lt, 20Lt
Colours: Clear.

Respecting The Environment:

  • 100% Lead Free.
  • Dispose of excess product and containers in a responsible manner without harming the environment.
  • This product is manufactured under strict SABS ISO 9001 quality standards.

Features

  • Sheds off liquid water and eliminates absorption.
  • Reduction of efflorescence.
  • Impedance of fungal growth.
  • Protects joints from decay.
  • Prevent staining of stone and brick work.
  • 100% lead free.

Intended Usages

  • A moisture barrier sealer used on unpainted bricks, concrete, stone, fibre cement, cinder block and other masonry materials.

Application Details

  • Mixing: Not applicable.
  • Method: Roller, brush or spray.
  • Thinning: Not required.
  • Cleaning: Remove as much of the product as possible from the application equipment before cleaning with ProGold Mineral Turpentine.

Conditions:

  • Temperature between 5°C and 40°C.
  • Relative humidity of less than 85%, preferably between 10: 00 and 16: 00.

Drying time: 
4 hours. 
Note:  Higher temperatures will accelerate the drying times (approximately halved for every 10°C increase), whilst lower temperatures will retard the drying time (approximately doubled for every 10°C decrease).

Recoating time:
 24 hours at 23°C with a substrate moisture contents of 15% or below.

Requirements:
 2-4 coats depending on the porosity of the surface.

Surface Preparations

  • Remove all dirt, loose material, grime, moss and fungus.
  • Repair any defective brickwork.
  • Leave new cement plaster to cure for 28 days before application.

Limitations

  • Cannot be overcoated.
  • Application to wet areas can lead to damp forming on the interior of that specific wall.
  • Annual maintenance coats may be required.
  • Not for use on walkways.

Safety

  • Keep out of reach of children.
  • Ensure to maintain good ventilation during application and drying process.
  • In case of skin contact, wash with soap and water or a recognised skin cleaner. Avoid contact with eyes. In case of contact with eyes rinse immediately with running water and seek medical advice.
  • If product is ingested drink plenty of water or milk. Do not induce vomiting at any time. Seek medical advice.
  • Refer to the Material Safety Data Sheet (MSDS) for detailed information about the product and transportation and classification criteria. MSDS is available on www.prominentpaints.co.za or from Prominent Customer Service Department.
  • To avoid any risk of spillage, always transport in a secure upright position.
  • Keep out of reach of children.
  • Ensure to maintain good ventilation during application and drying process.
  • In case of skin contact, wash with soap and water or a recognised skin cleaner. Avoid contact with eyes. In case of contact with eyes rinse immediately with running water and seek medical advice.
  • If product is ingested drink plenty of water or milk. Do not induce vomiting at any time. Seek medical advice.
  • Refer to the Material Safety Data Sheet (MSDS) for detailed information about the product and transportation and classification criteria. MSDS is available on www.prominentpaints.co.za or from Prominent Customer Service Department.
  • To avoid any risk of spillage, always transport in a secure upright position.

Copyright © 2017 Prominent Paints