Neutron

Neutron Plaster Primer

PrintEmail

A solvent based acrylic solution primer for porous and chalky surfaces. To improve adhesion of subsequent coats of paint and also to form a barrier against alkali attack on subsequent coats.

Products Applications:
Primers

Purchase:
Neutron Plaster Primer is available in the following sizes: 1lt , 5lt and 20lt 


Description

Appearance: Matt finish.
Spreading Rate: 3 - 6m²/litre depending on surface porosity and texture.
Solids: ± 70% by mass and ± 50% by volume.
Density: 1,38 kg/litre.
Recommended Dry Film Thickness: 25-30µm per coat minimum.
Viscosity: ± 80Kµ.
Flash Point: 43°C.

Storage:

  • Keep containers properly sealed.
  • Store away from direct heat, sun and severe cold in a place with adequate ventilation.

Available Sizes: 1 lt, 5 lt and 20 lt
Colours: White.

Respecting The Environment:

  • 100% Lead Free.
  • Dispose of excess product and containers in a responsible manner without harming the environment.
  • This product is manufactured under strict SABS ISO 9001 quality standards.

Features

  • Alkali resistant: Protects subsequent coats against alkali attack.
  • Good penetration: Dissolved binder penetrates porous surfaces and seals them off.
  • Good adhesion: To porous, correctly prepared chalky surfaces.

Intended Usages

  • Superior primer for new interior and exterior cement plaster.
  • Primer for gypsum plaster, hardboard, gypsum boards, rhinolite and glasstone.

Application Details

  • Mixing: Stir well before use with a flat paddle to an even consistency. Stir occasionally during use.
  • Method: Brush or roller.
  • Thinning: ProGold Mineral Turpentine.
  • Cleaning: Remove as much of the product as possible from the application equipment before cleaning with ProGold Mineral Turpentine.

Conditions:

  • Temperature between 5°C and 40°C.
  • Relative humidity of less than 85%, preferably between 10: 00 and 16: 00.
  • Ideally, apply when the temperature of the substrate is at least 2ºC above dew point.
  • If possible away from direct sunlight.

Drying time: 
Surface dry:  4 hours, Hard dry:  8 hours at 23ºC.
Note:  higher temperatures will accelerate the drying times (approximately halved for every 10ºC increase), whist lower temperatures will retard the drying times (approximately doubled for every 10ºC decrease).

Recoating time:
 16 Hours at 23 ºC.

Requirements:
 One coat.

Surface Preparations
Cement Plaster:

  • Apply directly.

Gypsum Plaster:

  • Apply directly.

Gypsum board, hardboard:

  • Apply directly.

Chalky paint:

  • Remove chalkiness and then apply.
  • Conduct a masking tape adhesion test 24 hours after application to ensure that good adhesion is established before overcoating.

Not recommended for redecorating - Primer only.

Limitations

  • Use limited to that of a primer only.
  • Neutron Plaster Primer is not a cure for damp problems.
  • Can only be used on absorbent surfaces.
  • Moisture content must not exceed 15 %.
  • Needs to be overcoated as it is not UV stable.

Safety

  • Keep out of reach of children.
  • Ensure to maintain good ventilation during application and drying process.
  • In case of skin contact, wash with soap and water or a recognised skin cleaner. Avoid contact with eyes. In case of contact with eyes rinse immediately with running water and seek medical advice.
  • If product is ingested drink plenty of water or milk. Do not induce vomiting at any time. Seek medical advice.
  • Refer to the Material Safety Data Sheet (MSDS) for detailed information about the product and transportation and classification criteria. MSDS is available on www.prominentpaints.co.za or from Prominent Paints Customer Service Department.
  • To avoid any risk of spillage, always transport in a secure upright position.

 

  • Keep out of reach of children.
  • Ensure to maintain good ventilation during application and drying process.
  • In case of skin contact, wash with soap and water or a recognised skin cleaner. Avoid contact with eyes. In case of contact with eyes rinse immediately with running water and seek medical advice.
  • If product is ingested drink plenty of water or milk. Do not induce vomiting at any time. Seek medical advice.
  • Refer to the Material Safety Data Sheet (MSDS) for detailed information about the product and transportation and classification criteria. MSDS is available on www.prominentpaints.co.za or from Prominent Paints Customer Service Department.
  • To avoid any risk of spillage, always transport in a secure upright position.

Copyright © 2017 Prominent Paints