Roof & Floor

Industrial Bituminous Aluminium Paint

PrintEmail

A high quality bituminous aluminium paint with good heat deflecting and anti-corrosive properties.

Products Applications:
Roof & Floor

Purchase:
Prominent Bituminous Aluminium Paint is available in the following sizes: 1lt , 5lt and 20lt 


Description
  • Appearance: Silver lustre
  • Spreading Rate: 12 - 14 m²/litre depending on surface texture.
  • Solids: ± 65% by mass and ± 65% by volume.
  • Density: 0,96 kg/litre.
  • Recommended Dry Film Thickness: 2 coats at 25µm per coat minimum.
  • Recommended Wet Film Thickness: 2 coats at 38µm per coat minimum.
  • Viscosity: 60 Kµ.
  • Flash Point: 43°C.

Storage:

  • Keep containers properly sealed.
  • Store away from direct heat, sun and severe cold in a place with adequate ventilation.

Available Sizes: 1Lt, 5Lt, 20Lt
Colours: Silver

Respecting The Environment:

  • Lead Free.
  • Dispose of excess product and containers in a responsible manner without harming the environment.
  • This product is manufactured under strict SABS ISO 9001 quality standards.

 

Features

  • Excellent exterior durability and UV resistance.
  • Goes on directly to surfaces without priming.
  • Bitumen content adds to water resistance of the coating.
  • Highly reflective.
  • Lead free.

Intended Usages

  • Exterior finish for steel and galvanised iron.
  • Roof coating on weathered galvanised iron.
  • Steel fencing.

Application Details
Mixing: Since the aluminium pigment settles very easily must it be stirred well before and during use with a flat paddle to an even consistency.
Method: Roller, oval brush or airless spray.
Thinning: Not recommended but 10% maximum with ProGold Mineral Turpentine if required.
Cleaning: Remove as much of the product as possible from the application equipment before cleaning with ProGold Mineral Turpentine.
Conditions:
Temperature between 5°C and 40°C. Relative humidity of less than 85%, preferably between 10: 00 and 16: 00. Ideally apply when the temperature of the substrate is at least 2°C above dew point. If possible away from direct sunlight.
Drying time: Surface dry - 12 hours, Hard dry - 48 hours at 23°C.
Recoating time: 48 hours at 23°C. Note:  Higher temperatures will accelerate the drying times (approximately halved for every 10°C increase), whilst lower temperatures will retard the drying time (approximately doubled for every 10°C decrease).
Requirements: One coat for recoating, two coats for new work.

Surface Preparations
New steel and galvanised iron:

  • Degrease with ProGold General Purpose Cleaner/water solution (1: 10) and abrasive pad.
  • Rinse with clean water and then apply directly.

Weathered galvanised iron:

  • Remove rust, clean with ProGold General Purpose Cleaner/water solution (1: 10) and abrasive pad, rinse with clean water and then apply directly.

Rusted steel:

  • Remove rust, clean with ProGold General Purpose Cleaner/water solution (1: 10) and abrasive pad, rinse with clean water and then apply directly.

Bitumen Aluminium:

  • Clean with ProGold General Purpose Cleaner/water solution (1: 10), rinse with clean water and then apply directly.

Previously Painted Surface in Good Condition:

  • Clean with ProGold General Purpose Cleaner/water solution (1: 10), rinse with clean water and then apply directly.

Previously Painted Surface in Poor Condition:

  • Remove and treat as new work.

Limitations

  • Not recommended for use on bituminous waterproofing and/or coatings.
  • Use limited to protection of steel and galvanised iron.
  • Not a heat resistant aluminium finish.
  • Cannot be used over Prominent Rust Primer or Prominent Galvanised Iron Primer.
  • Cannot be overcoated with emulsion paint.
  • Prominent Bituminous Aluminium Paint must NOT be applied to roofs that act as catchments for drinking water.
  • Product should not be applied to areas which will remain submerged under water.
  • Good weather resistance, but normal fading takes place over time.
  • A maintenance coat 2-3 years after completion of the project will be required for continual protection and correct product performance.

Safety

  • Keep out of reach of children.
  • Ensure to maintain good ventilation during application and drying process.
  • In case of skin contact, wash with soap and water or a recognised skin cleaner. Avoid contact with eyes. In case of contact with eyes rinse immediately with running water and seek medical advice.
  • If product is ingested drink plenty of water or milk. Do not induce vomiting at any time. Seek medical advice.
  • Refer to the Material Safety Data Sheet (MSDS) for detailed information about the product and transportation and classification criteria. MSDS is available on www.prominentpaints.co.za or from Prominent Customer Service Department.
  • To avoid any risk of spillage, always transport in a secure upright position.
  • Wet product is flammable and naked should not be allowed in the vicinity of the working area.
  • Always wear gloves when working with the product and avoid excessive inhalation and skin contact.
  • Keep out of reach of children.
  • Ensure to maintain good ventilation during application and drying process.
  • In case of skin contact, wash with soap and water or a recognised skin cleaner. Avoid contact with eyes. In case of contact with eyes rinse immediately with running water and seek medical advice.
  • If product is ingested drink plenty of water or milk. Do not induce vomiting at any time. Seek medical advice.
  • Refer to the Material Safety Data Sheet (MSDS) for detailed information about the product and transportation and classification criteria. MSDS is available on www.prominentpaints.co.za or from Prominent Customer Service Department.
  • To avoid any risk of spillage, always transport in a secure upright position.
  • Wet product is flammable and naked should not be allowed in the vicinity of the working area.
  • Always wear gloves when working with the product and avoid excessive inhalation and skin contact.

Copyright © 2017 Prominent Paints