Industrial

Industrial Machinery Enamel Primer

PrintEmail

Corrosion resistant metal primer based on a short oil alkyd.

Products Applications:
Primers and Industrial

Purchase:
Prominent Machinery Enamel Primer is available in the following sizes: 1lt , 5lt and 20lt 


Description

Appearance: Matt finish.
Spreading Rate:8 - 12 m²/litre depending on surface texture.
Solids: ± 55% by mass and ± 45% by volume.
Density: ± 1,20 kg/litre.
Recommended Dry Film Thickness: 25 µm per coat.
Recommended Wet Film Thickness: 55 µm per coat
Viscosity: 65 Kµ.
Flash Point: 23°C.

Storage:

  • Keep containers properly sealed.
  • Store away from direct heat, sun and severe cold in a place with adequate ventilation.

Available Sizes: 1Lt, 5Lt, 20Lt
Colours: Red, Grey

Respecting The Environment:

  • 100% Lead Free.
  • Dispose of excess product and containers in a responsible manner without harming the environment.
  • This product is manufactured under strict SABS ISO 9001 quality standards.

Features

  • Quick drying.
  • Can be overcoated after 2 hours.
  • Corrosion resistant.
  • 100% lead free.

Intended Usages

  • New, unrusted metal as a primer.

Application Details

  • Mixing: Stir before use with a flat paddle to an even consistency. Stir occasionally during use.
  • Method: Brush or spray.
  • Thinning: ProGold Lacquer Thinners.
  • Cleaning: Remove as much of the product as possible from the application equipment before cleaning with ProGold Lacquer Thinners.

Conditions:

  • Temperature between 5°C and 40°C.
  • Relative humidity of less than 85%, preferably between 10: 00 and 16: 00.
  • Ideally apply when the temperature of the substrate is at least 2°C above dew point.

Drying time: 
Surface dry - 15 minutes, Hard dry - 2-3 hours at 23°C with a relative humidity of 85% or less. 
Note:  Higher temperatures will accelerate the drying times (approximately halved for every 10°C increase), whilst lower temperatures will retard the drying time (approximately doubled for every 10°C decrease).

Recoating time: 2 hours to 14 days.
Requirements: One coat.

Surface Preparations

  • De-rust and degrease using ProGold General Purpose Cleaner/water mixture (1: 5), rinse with clean water, allow to dry and apply one coat.
  • Not for redecorating.

Limitations

  • Poor anti-corrosive properties on rusted steel.
  • Cannot be overcoated with Prominent 2 Pack Floor Epoxy or Prominent 2 Pack Polyurethane Floor coating.
  • Thicker coatings take longer to dry thoroughly.
  • Wrinkling can occur if recoating times are not adhered to.
  • To ensure a consistent appearance ensure that batch numbers on all the containers are the same. Where the batch numbers differ, intermix before use.

Safety

  • Keep out of reach of children.
  • Ensure to maintain good ventilation during application and drying process.
  • In case of skin contact, wash with soap and water or a recognised skin cleaner. Avoid contact with eyes. In case of contact with eyes rinse immediately with running water and seek medical advice.
  • If product is ingested drink plenty of water or milk. Do not induce vomiting at any time. Seek medical advice.
  • Refer to the Material Safety Data Sheet (MSDS) for detailed information about the product and transportation and classification criteria. MSDS is available on www.prominentpaints.co.za or from Prominent Customer Service Department.
  • To avoid any risk of spillage, always transport in a secure upright position.

 

  • Keep out of reach of children.
  • Ensure to maintain good ventilation during application and drying process.
  • In case of skin contact, wash with soap and water or a recognised skin cleaner. Avoid contact with eyes. In case of contact with eyes rinse immediately with running water and seek medical advice.
  • If product is ingested drink plenty of water or milk. Do not induce vomiting at any time. Seek medical advice.
  • Refer to the Material Safety Data Sheet (MSDS) for detailed information about the product and transportation and classification criteria. MSDS is available on www.prominentpaints.co.za or from Prominent Customer Service Department.
  • To avoid any risk of spillage, always transport in a secure upright position.

Copyright © 2017 Prominent Paints