Exterior

Woodpro Wood Varnish

PrintEmail

An alkyd based varnish for interior and exterior wood with good UV resistant properties for a long lasting high quality protection.

*WOOD VARNISHED, PREVIOUSLY LABELLED AS PP WOODDRESSING.

Products Applications:
Wood (Interior), Wood, Varnish (Wood), Wood (Exterior) and Wood (Interior & Exterior)

Purchase:
Prominent Woodpro Wood Varnish is available in the following sizes: 1lt and 5lt 


Description

Clear and colours as per product brochure.

Appearance: Suede finish.
Spreading Rate: 10 - 15 m²/litre. The practical spreading rate depending on the porosity and profile of the wood as well as the application technique and tools used. 
Solids: ± 55% by mass and ± 50% by volume.
Density: ± 0,90 kg/litre.
Recommended Dry Film Thickness: 15 to 20 µm microns per coat.
Viscosity at 23°C: ± 60 Kµ.
Flash Point: 23°C.

Storage:

  • Keep containers properly sealed.
  • Store away from direct heat, sun and severe cold in a place with adequate ventilation.

Available Sizes: 1Lt, 5Lt.

Colours: Clear and colours as per product brochure.

Respecting The Environment:

  • 100% Lead Free.
  • Dispose of excess product and containers in a responsible manner without harming the environment.
  • This product is manufactured under strict SABS ISO 9001 quality standards.

Features

  • UV resistant finish
  • Good weathering and protection properties.
  • Water-resistant and moisture repellent.
  • Resistant to cracking and peeling.
  • Excellent adhesion and good abrasion resistance.

Intended Usages

  • Doors and window frames.
  • Furniture and garage doors.

Application Details

  • Mixing: Stir before use with a flat paddle to an even consistency. Stir occasionally during use.
  • Method: Brush and short nap roller.
  • Thinning: Not recommended but 10% maximum if required with ProGold Mineral Turpentine.
  • Cleaning: Remove as much of the product as possible from the application equipment before cleaning with ProGold Mineral Turpentine.

Conditions:

  • Temperature between 5°C and 40°C.
  • Relative humidity of less than 85%, preferably between 10: 00 and 16: 00.

Drying time: 
Touch dry - 6 hours, Hard dry - 24 hours. 
Note:  Higher temperatures will accelerate the drying times (approximately halved for every 10°C increase), whilst lower temperatures will retard the drying time (approximately doubled for every 10°C decrease).

Recoating time:
 24 hours.

Requirements:
 2 coats min for new wood.

Surface Preparations & Application

  • All surface to be clean dry and sound.
  • Remove any oil, grease, plaster splatter, etc.
  • All surfaces to be coated should be sound, clean, dry and free from sawdust and loose, flaking material after using the correct preparation method and products.
  • Stir product regularly with a flat paddle to achieve an even consistency before and during application process.
  • Apply product using the application method icons guideline.

New Wood:

  • Sand the surface with 150-180 grit sandpaper (sand with the grain to eliminate damage to wood surface).
  • Remove sanding dust from surface with a clean damp cloth or paintbrush.

Previously varnish wood in good condition: 

  • Sand to a matt finish to provide a key.
  • Remove dust with a damp cloth. 

Previously varnish wood in poor condition:

  • Strip completely by deep sanding or by using a paint stripper for wood.
  • Rinse thoroughly with clean water to neutralise and allow drying.
  • Sand to a smooth surface finish.
  • Remove dust with a damp cloth.

Previously coated with a wax sealer/oil based wood preservative:

  • Mechanically sand until raw wood is exposed with no product residue. Wipe clean with a damp ProGold Mineral Turpentine cloth to neutralise and to remove saw dust.

Weathered or Discoloured wood:

  • Remove the weather or discoloured layers by sanding with a 100 grit sandpaper to an even smooth finish.
  • Remove dust with a damp cloth.
  • Alternatively treat wood with a wood reviver to remove any weather damage and to neutralise the wood surface, allow drying.
  • Sand to a smooth finish.
  • Remove dust with a damp cloth.

Previously painted wood:

  • Strip completely by deep sanding or by using a paint stripper for wood.
  • Rinse thoroughly with clean water to neutralise and allow drying.
  • Sand bare wood to a smooth surface finish.
  • Remove dust with a damp cloth.

Limitations

  • ForAs with all wood coating products routine inspections are needed every 12 months. It is recommended to apply a maintenance coat every 12 months or when the wood appears dry to prolong the life of the WOODPRO WOOD VARNISH.
  • Can only be applied under specified conditions.
  • Cannot be applied directly over previous wood treatments without the correct preparation.
  • When coating exterior wood special attention must be given to the adequate sealing and coating of the end grain.
  • Only apply product to dry wood in a dust free environment.
  • To ensure a consistent appearance ensure that the batch numbers on all containers are the same. Where batch numbers on containers differs intermix before use.
  • Not for use below ground level.
  • Not recommended for use on exterior decking wood.
  • Cannot be tinted with Universal Stainer. 

Safety

  • KeepKeep out of reach of children.
  • Ensure to maintain good ventilation during application and drying process.
  • Wear a suitable dust mask if sanding.
  • In case of accidental skin contact, wash with soap and water or a recognised skin cleaner. Avoid contact with eyes. In case of contact with eyes rinse immediately with running water and seek medical advice.
  • If product is ingested drink plenty of water. Do not induce vomiting at any time. Seek medical advice.
  • Do not smoke while painting.
  • To avoid any risk of spillage, always transport in a secure upright position.
  • Refer to the Material Safety Data Sheet (MSDS) for detailed information about the product and transportation and classification criteria. MSDS is available on www.prominentpaints.co.za or from Prominent Customer Service Department.
  • Keep out of reach of children
  • Ensure to maintain good ventilation during application and drying process.
  • Wear a suitable dust mask if sanding.
  • In case of accidental skin contact, wash with soap and water or a recognised skin cleaner. Avoid contact with eyes. In case of contact with eyes rinse immediately with running water and seek medical advice.
  • If product is ingested drink plenty of water. Do not induce vomiting at any time. Seek medical advice.
  • Do not smoke while painting.
  • To avoid any risk of spillage, always transport in a secure upright position.
  • Refer to the Material Safety Data Sheet (MSDS) for detailed information about the product and transportation and classification criteria. MSDS is available on www.prominentpaints.co.za or from Prominent Customer Service Department

Copyright © 2017 Prominent Paints